Measure
Reading sizes, distances and angles off the model, and a body's volume, mass and inertia.
The Inspect menu holds every check in one place: the measure tool and the clipping plane, then each workbench's checks under its name (the Assembly's interference and mass, the Surface workbench's continuity, curvature map and zebra stripes). A check of another workbench switches to it and starts the check.
The measure tool
Measure on the view's pill (or Inspect › Measure) arms the tool; press it again, or Escape, to put it away. It has no key by default; Preferences › Keyboard can give it one. While it is armed, clicks in the view pick things to measure instead of selecting them, and a prompt beside the cursor says what to pick next. Pan, orbit and zoom work as always (Camera).
A click picks, in this order:
- the edge under the cursor, when one is within reach
- a datum (a plane, a line, a point or a coordinate system's origin)
- the face under the cursor, the whole face and not just the point
- else the point clicked
Each pick is pinned with a dot numbered 1, 2, 3… in the order picked, the same size on screen at any zoom; the picks are joined by a line, and the readout stands beside the last two. In the split view a pick on a body of the pane beside the viewport is pinned there. The log keeps every readout too.
One pick
| Pick | Reads |
|---|---|
| Straight edge | Length |
| Circular edge | Radius, diameter and length |
| Flat face | Area |
| Cylinder or sphere face | Area, radius and diameter |
| Cone face | Area, half angle and cone angle |
| Torus face | Area, major radius, minor radius and tube diameter |
| Datum point or coordinate system | Its name and position |
| Datum plane or line | Its name |
| Point | Its X, Y and Z |
Two picks
The second pick is measured against the first:
- Distance between them. Two parallel flat faces or datum planes read the distance square across. A point against a plane reads Distance to plane, and against an axis Distance to axis, both square to it. Otherwise the distance is between the points picked, with its Δx, Δy and Δz.
- Least distance when both picks are faces or edges of bodies: the kernel works out the shortest distance between the two, face to face, edge to edge or edge to face, and a dashed line joins the closest points. It reads "…" while it is being worked out.
- Axis distance when both have an axis: a round face, a circular edge or a datum line.
- Angle when both have a direction: a straight edge's, a circle's or a round face's axis, a flat face's normal, a datum plane's normal or a datum line's direction.
Chains
Picks run on in a chain: each new pick is measured against the one before it, and the chain's totals follow it:
- Path through N picks: the length of the line through every pick.
- Total length when every pick is an edge.
- Total area when every pick is a face.
A click on empty space starts the chain over, as does Start over on the tool's bar under the view toolbar.
Units
The tool's bar sets the unit its readout is in: Document (the document's own unit) or mm, cm, m, in or ft. The choice is saved with the document.
Quick measure in the status bar
The status bar can show what the selection measures, without the tool: right-click the bar and turn on Quick measure (it starts off). Select faces and edges as usual (Editing) and the bar reads them as the tool would: one face's area and sizes, the least distance and angle between the last two, the totals of several. The bar shows the first lines; hovering it shows them all. It reads in the document's unit.
Mass of the selection
With bodies selected (in the view, several with Ctrl or a box, or a body, part or component in the tree), the status bar shows their mass and volume together, and follows the selection. The material name beside them picks what the mass is reckoned in, from the same list as a body's Appearance material (PLA at start); a body with a material of its own is weighed at that. A figure taken from a mesh starts with ≈. Right-click the bar to turn Mass off.
The Physical group
The property panel's Physical group measures the body it shows: its Volume, Surface area and centre of mass (Centre X, Y, Z), and its Mass once the body has a material. A figure taken from the body's mesh rather than its exact shape starts with ≈.
Below them is the body's inertia. Inertia about chooses what it is taken about:
- Centre of mass (the default) or Origin: the inertia tensor (Ixx, Iyy, Izz, Ixy, Ixz, Iyz) on the world's axes, then the principal moments I1 to I3, smallest first, each with its axis.
- X axis, Y axis, Z axis, an edge picked in the view (Picked edge, or Picked edge's axis for a round one), a round face's axis (Picked face's axis), or a datum line: the Moment about that line and the Gyration radius, how far from the line the whole mass would turn alike.
- A datum point or coordinate system, by name: the tensor and principal moments about that point.
With a material the moments are the mass's, in g times the unit squared; without one they are the volume's at unit density, in the unit to the fifth.
For a whole assembly, the Assembly's Mass and centre of mass tool weighs every visible body and gives the assembly's principal moments of inertia about its centre of mass (Assembly).